How To Install A Sony Car Stereo

Download Article

Download Article

Installing a new car stereo can ofttimes be simple plenty to do yourself, and his commodity will provide yous with a general guide on how to do it. Keep in mind that some cars and systems are more complicated than others and that every car and stereo arrangement volition be unlike, so some specifics may vary. Be certain to read any instructions that come up with the new car stereo before attempting to install information technology.

1. one

   Set up the parking brake and disconnect the negative cable from your motorcar battery. Exist sure to practice this to avoid short-circuiting the electrical organization during the installation, which could lead to fire or physical harm for y'all.^[1]

   • For instructions on disconnecting the bombardment, come across How to Disconnect a Automobile Battery.

2. 2

   Unscrew whatsoever screws that are securing the trim in place. Be careful to remove all screws earlier trying to pry off the trim or you lot may break it.^[2]

   Advertisement

3. 3

   Remove the trim. For some cars, y'all may need to remove several pieces of plastic trim, usually working from the bottom up.^[3]

   • If you need to remove trim that includes any knobs or drawers, remove them earlier trying to pry off the trim.
   • Use your easily or a pry tool to pry off each piece of trim. Pry tools are specifically for this purpose and will non damage the trim pieces.

4. 4

   Pull out any necessary components. If you demand to remove any components before beingness able to admission the stereo, practice and so.

   • Disconnect components that are wired to the car. Take a picture show of how each is wired for later reference.

5. 5

   Loosen the stereo. Different cars may have varying elements securing the stereo in place.

   • If the stereo is held in place by screws or nuts, loosen them with the appropriate tool (screwdriver or nutdriver, respectively).
   • If the stereo isn't held in place by screws or nuts, y'all'll need to use a radio-removal central. This tool is commonly necessary in Ford vehicles. Radio-removal keys (sometimes besides referred to as radio-removal tools) volition typically either be in an elongated horseshoe shape or will have a circular shape at 1 stop and a notched shaft at the other. They're bachelor at virtually auto-parts stores.
   • Insert the keys into the two small slots in the face of the stereo. You will release a mechanism holding the stereo in place. Slide the radio-removal keys into each slot again until you lot feel the stereo loosen from in its housing. Y'all should and so be able to pull out the stereo relatively hands.

6. half-dozen

   Pull the stereo out of the panel. You may want to use needle-nose pliers to grip the edge of the stereo and aid yous pull it out.^[4] Pull it gently, and if the stereo doesn't come out easily, double bank check that yous oasis't missed any components that may be holding information technology in place.

7. 7

   Have a picture of how the stereo is wired. This is an important step because the photo will serve equally a reference later when y'all're wiring in the new stereo.

8. eight

   Unplug the stereo connections. You'll see a series of wires continued to the dorsum of the stereo, and y'all'll need to disconnect each of them.

   • First unplug the antenna wire, which volition typically be a thicker wire plugged in separately from the residuum. In one case it's unplugged, you should exist able to move the stereo around more freely.
   • Next unplug the each of the wire harness connectors. There will typically be several of these and you tin recognize them because a serial of wires will feed into each one. The plastic piece into which the wires are fed should accept either a tab or a button yous tin button, which will release the harness.

   Advertisement

1. 1

   Match up the wires. Match the wires of the car'due south harnesses to the new stereo'south harnesses. Each harness connector is unique, so it should be piece of cake to figure out which ones fit together.

   • To exist rubber, check the wiring diagrams for both your auto and the new stereo to verify you've continued them correctly.
   • If your automobile'due south stereo doesn't utilize wire harnesses, you'll need to lucifer upwardly each wire manually. The wires are color-coded; however, the wires on an after-market place stereo may non lucifer with the color-coded wires in your vehicle. It'southward best to report and follow the wiring diagram that came with the stereo.
   • Connect the matched wires. There are two options for connecting the wires, crimping or soldering. Crimping is faster and easier, only soldering will provide a more stable and secure connection. Exist sure to use the proper size crimper and don't try to bundle the wires with tape — it will eventually dry out and fall off. Bundle wires using naught ties instead.^[5]

2. 2

   Gather the mounting kit. If your new stereo came with a separate mounting kit, assemble it according to the stereo'south instructions (information technology will often hateful plumbing fixtures a metal housing sleeve into the mounting frame).

   • Push down on the tabs located around the metal sleeve with a screwdriver to secure the metal sleeve in identify.

3. 3

   Connect the ability source. Typically, if you have a wiring harness, this connexion will be made when y'all connect the new stereo harnesses to the harnesses in the machine.

   • If you lot aren't using a wiring harnesses, yous'll demand to manually connect the power. Decide whether your machine has a switched power source (typically a cherry wire) or a constant ability source (typically a yellow wire). Some vehicles even accept both types of power sources. For more information on switched versus constant power, become here.

4. 4

   Ground the stereo. If you're using wiring harnesses, this connection will be fabricated when you lot connect the harness pieces.

   • If you aren't using a wiring harness, y'all'll need to locate the bolt, wire, or spiral that connects with the car's bare metal chassis. Loosen the bolt, wire, or screw and slip the stereo's ground wire (usually black) underneath, so tighten.
   • Annotation that the ground connection is important to the optimal performance of the stereo. If the footing wire doesn't connect to the bare metallic, it won't work. And if the ground wire connexion is loose, it could upshot in poor audio output. Sand down the expanse with sand paper to ensure a good connectedness.

5. 5

   Connect the remaining wires. Plug in the antenna cablevision and connect the stereo's wiring adapter to the the motorcar's wire harness. Connect the output converter if i is needed to brand the new stereo compatible with the auto's audio system. Have in mind that all wires should be connected in the end and at that place should no single one hanging unattended.

6. 6

   Test the stereo. Turn the power on and test the AM, FM, and CD components. Examination the fade and rest settings to be sure the speakers are working properly. Plow the power back off.

   Advert

1. 1

   Button the stereo into place. When the stereo is fully in, you should hear it click into place.

2. 2

   Reconnect the components. Fasten in any screws that are needed to hold the stereo in identify, reconnect any wired components, and supercede whatsoever knobs or drawers that were removed.

3. 3

   Snap all the pieces of trim dorsum into place over the stereo. Double check that all screws and trim pieces are securely in place.

4. 4

   Try out the new stereo. Turn the motorcar ability on again and play effectually with the stereo and its settings to be sure everything is in working club.

   Advertisement

Add New Question

• Question

  How do I supplant a 1996 Jeep radio with a Pioneer radio by matching the wires manually?

  

  It should be red to green, orange to purple, maroon to turquoise, pinkish to silver, and clear to black.

• Question

  How do I connect the stereo to the equalizer if the stereo has no input port?

  

  You have to buy an adapter cable. If you buy from a store like Radio Shack, you may be able to become the salesman to come exterior and assistance y'all install information technology... For free!

• Question

  If I have an aftermarket Pioneer radio, and want to supersede it with another Pioneer radio, practise I need a new wiring harness?

  

  Not necessarily, just compare the harnesses and in one case they match, you can become ahead.

• Question

  Can the radio short out my battery?

  

  The radio tin drain the battery, but should not brusque information technology out.

• Question

  Where can I connect an amp remote if a stereo does not have a remote on cable?

  

  Utilize the factory fuse box. Discover a wire that turns on/off with the ignition key.

• Question

  What practice I do if the stereo won't piece of work after I disconnected it and put it back together?

  

  Check your connections. Brand sure yous have 12 volts to hot wire and a practiced ground. Some head units accept a separate wire that must go to voltage for the display separately.

• Question

  What's the difference between an amp and a booster?

  

  Some people consider them the same. Even so, I would say that a booster is a 'become between' only to increase the power input to a subwoofer (or set of subwoofers), whereas an amplifier is to increment the power to all channels. Some amps too volition provide an exclusive (or dedicated) output for a subwoofer or set of subwoofers in addition to the RF RR LF LR 4 channels.

• Question

  I have a second hand Peugeot 307 with a hole in the dashboard where a radio used to be. Is information technology a simple case of plugging in some connectors to a new radio unit?

  

  This will work only if you replace with a stereo with same connectors.

• Question

  Do I have to unhook the battery?

  

  No, simply it doesn't hurt as a expert prophylactic precaution to prevent electric daze.

• Question

  Tin can I get an adapter for a car stereo if the connectors are dissimilar?

  

  Very oftentimes, yep. Retailer sites like Crutchfield and Amazon will show y'all what's needed to connect a radio you lot bought there to dissimilar makes and models of car. They're ordinarily not strictly necessary but can simplify the installation.

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Advertisement

• Be certain to buy a stereo that will fit your machine'due south make and model. If yous demand help deciding what to buy, get to an electronics store or a store specializing in car electronics and enquire for assistance choosing a stereo. If a stereo does non fit there are may be an aftermarket kits available to make it fit. For more information, become here.

• Some retailers may offering to install your stereo for gratis or minimal price if you lot purchase it from them, so exist sure to inquire.

• When removing whatsoever screws or nuts, place them in the car'southward cup holder so they don't go lost.

• To make joining the wires easier, run across if in that location is an adapter that connects your quondam harness to the new stereo.

Ad

• Follow the specific instructions provided with the new stereo. Some of the installation steps may be specific to your car and stereo.

• If you detect yourself feeling lost or frustrated, get aid from a professional — otherwise you lot may impairment the auto or injure yourself.

Advertising

Things You'll Need

• A car with a stereo system
• A new stereo
• Phillips and flat head screwdrivers (depending on model)
• Nutdriver (depending on model)
• Radio-removal keys (depending on model)
• Pry tool (optional)
• Needle nose pliers (optional)
• Zip ties
• Electrical tape
• Soldering gun or crimp connectors

About This Commodity

Article Summary Ten

To install a motorcar stereo, match the wires of the car's harnesses to the new stereo's harnesses. Each harness connector is unique, and so it should be easy to figure out which ones fit together, but you tin can bank check the wiring diagrams for your auto and your new stereo if you lot're not sure. If your car's stereo doesn't apply wire harnesses, you lot'll need to lucifer up each wire individually. Assemble the mounting kit if your stereo came with one, then slide the stereo into identify and spike any screws that are needed to hold the stereo in place. Keep reading to larn how to take out your original stereo!

Did this summary help you?

Thanks to all authors for creating a page that has been read i,064,167 times.

Is this article upwards to date?

Source: https://www.wikihow.com/Install-a-Car-Stereo

Posted by: leeparunt.blogspot.com

Share this post